top of page
WGTechno drip tape

Buy WGTechno Drip Tape online

See Drip Tape prices on Rexporta

WGTechno Drip Tapes

Our drip tapes are with wgtechno quality at the best prices.
Thickness: 7 and 8 microns.
dripper distance options: 10-20-25-30 cm.
Amount of dripping water: 1-1.4-1.6-1.8 liters per hour.
Roll length: 500-1000-2500 meters

16 mm flat drip tape with large dripper

22 mm flat drip tape with large dripper

Our drip tapes are with wgtechno quality at the best prices.
Thickness: 7 and 8 microns.
dripper distance options: 10-20-25-30 cm.
Amount of dripping water: 1-1.4-1.6-1.8 liters per hour.
Roll length: 100-400-800 meters

Drip irrigation fittings and valves

Drip Tape Fittings

Drip Tape fittings
Round drip pipe fittings
Dripline Barbed Fittings
Drip irrigation valves
Drip irrigation valves
Drip tape valves
Drip Tape Fittings
dripper and sprayer

Online Drippers

WGTechno online dripper models
WGTechno pc online dripper
  • drippers working pressure: 1-3 bar

  • Be sure to use a filter to avoid clogging the dripper holes.

See Dripper prices on Rexporta

Buy WGTechno Drippers online

Benefits of Drip Irrigation

online dripper

Benefits of Drip Irrigation

Drip irrigation involves placing tubing with emitters on the ground along side the plants. The emitters slowly drip water into the soil at the root zone. Because moisture levels are kept at an optimal range, plant productivity and quality improve. In addition, drip irrigation:

  • Prevents disease by minimizing water contact with the leaves, stems, and fruit of plants.

  • Allows the rows between plants to remain dry, improving access and reducing weed growth.

  • Saves time, money, and water because the system is so efficient.

  • Decreases labor.

  • Increases effectiveness on uneven ground.

  • Reduces leaching of water and nutrients below the root zone.

 

Drip Irrigation System Design and Components

The main components of a drip irrigation system include the mainline, valve, sub-main, backflow preventer, pressure regulator, filter, tubing adapters and fittings, drip tubing, emitters, and end caps. You may find all these in WGTechno stores. The mainline is the pipe that runs from the water source – typically your outdoor faucet – to the valve; and the sub-main runs from the valve to the point where the drip tubing is connected. Generally, sub-mains are used only when there are multiple lines of drip tubing and zones feeding off of the same mainline water source. The combined length of the mainline and sub-main should not exceed 400 feet.
The valve controls water flow into the system and can be set for either automatic or manual control. Backflow preventers are necessary to ensure that irrigation water doesn’t flow back into the pipes and contaminate your main water source.
Pressure regulators are needed if the water pressure is over 2,75 bar. If you do not know your water pressure it is a good idea to install one just in case.
Filters keep dissolved substances in your water from clogging the emitters over time. Install filters either at the emitters or at the water source to protect both the valve and pressure regulator in addition to the emitters. It is best if the filter has at least a 150 mesh screen or higher.
Tubing adapters and fittings are used to attach the drip tubing to the rest of the system. It is important that these are the right size for the tubing to prevent them from blowing apart under pressure.

Drip Tubing and Emitters
Drip tubing is a polyethylene tube with emitters placed along the plants. The emitters release the water from the drip tubing. Drip tubing and emitters come in various types and diameters depending on your needs. The length of a single drip tube should not exceed 60 meters from the point where water enters the tube. You will need to stake the tubing to keep it from moving. As a rule, don’t bury the drip tubing and emitters, even if they are designed to be. This helps to prevent clogging and rodent damage.

Emitter Spacing and Design
Emitters can be spaced evenly for row crops, and this design is known as an emitter hose. Emitters can also be spaced intermittently for plants spaced further apart, such as trees, shrubs and perennials. With an emitter hose, the emitters will generally be spaced about 45 centimeters apart. When watering trees and shrubs, there should generally be two emitters per plant. Emitters typically have a flow rate of 4 liter per hour, though a flow rate of 2 liter per hour may be better for maximum efficiency. The end cap is placed at the end of the drip tubing to prevent water running out the end.

Basic Operation and Maintenance
Drip irrigation can be set to run automatically, like sprinklers, or controlled manually. Manual operation allows you to take advantage of rainfall before applying unnecessary water. For more information on automatic or smart irrigation , see WGTechno drip irrigation controllers page.

Because small amounts of water are applied slowly, drip irrigation is designed to run daily unless it rains. How long to run the drip irrigation system will depend on how much water plants require per day and the emitters’ flow rate. Water is applied either once or twice a day. Early morning is the best time to water because there will be less evaporation. Watering in the evening increases plant disease. WGTechno wifi soil sensor lets you know your humidity level and may control your irrigation automatically.

Check filters and emitters on a regular basis to ensure they are functioning properly and not clogged. To prevent winter damage, take up the drip irrigation system at the end of each gardening season.

Most suppliers/manufacturers of drip irrigation systems will provide specific design, installation, operation, and maintenance specifications and guidelines that should be carefully followed.
The cost of a drip irrigation system will vary depending on the size of the area to be irrigated and the type of emitters and tubing used. However, regardless of the size of the area being irrigated there is an initial upfront cost for standard items such as the valve, pressure regulator, and backflow preventer.

Effective Distances of Flat Drip Irrigation Pipes

Tape diameter & Emitter spacing   Flow                         7 Mil Flat Drip Tape (m)                  8 Mil Flat Drip Tape (m)

17 mm & 20 cm..........................................................................................73........................................................80

17 mm & 25 cm..........................................................................................85........................................................95

17 mm & 30 cm ...............................1,6 Lt/hour.....................................97........................................................106                                      

17 mm & 40 cm.........................................................................................120......................................................130

17 mm & 50 cm..........................................................................................140......................................................150

The trials were carried out on unsloping land under 1 ATM pressure. Distances are given for informational purposes based on a 10% flow difference over average values; It may vary depending on the application method and land structure.

"The highest recommended working pressure is 0.8 ATM for 6 Mil flat pipes and 1 ATM for 8 Mil flat pipes."

 

 

 

Effective Distances of Flat Drip Irrigation Pipes

Disc Filters

Irrigation controllers

Drip irrigation controllers and sensors

smart drip irrigation controller

Homgar smart irrigation system

The Homgar app allows you to manage and share irrigation schedules with family members. Additionally, the station records environmental data every 3 minutes and can pair up to 2 sensors, you can get smarter with your gardening by utilizing soil sensors for even more efficient watering.

With two independent outlets, it can work for two separate areas to run the watering plan according to the schedule.

When managing your garden's water supply by water usage or watering time. When paired with a soil sensor, each zone can be connected to a corresponding soil sensor separately and each zone can even automatically control water based on soil moisture.

Smart drip irrigation systems

When you are tired of flowers and shrubs whether they need watering.Test soil moisture, temperature, and sunlight with one moisture meter. Quickly helps you to know when you need to water your plants. Control the temperature and know whether the plants are getting adequate sunlight.

Weather station for irrigation

You don't have to pick up your mobile phone to get a clear picture of the data of the associated usb-devices on the display, such as indoor and outdoor temperature humidity,soil temperature and humidity, rainfall, flow meters, etc.,irrigation schedules, water consumption, etc.can be displayed.

At Mza Chitili, we are dedicated to providing you with the highest quality vegetable seedlings. Our greenhouse, located in Marneuli, Georgia, boasts 11,000 square meters of space, complete with modern infrastructure and expert staff. 

At WGTechno, we specialize in producing high-performance polyethylene pipes that meet your specific needs. Our HDPE polyethylene pipes are available in a range of diameters, pressure ratings and sizes, from 16mm to 160mm, and pressure classes PN4 to PN32.

Plastic Disc Filters are suitable for virtually any domestic, agricultural or industrial application .

High Quality non-corrosive materials of construction, consisting of high impact strength plastics.

bottom of page